germabuddies.blogg.se

1. #Icom 756 pro ii specifications manuals
2. #Icom 756 pro ii specifications driver
3. #Icom 756 pro ii specifications full
4. #Icom 756 pro ii specifications plus
5. #Icom 756 pro ii specifications series

You don't need to send me the entire radio, only the front panel. For Instructions on downloading your product manual, click HERE. The cost of shipping the front panel both ways is not included.

#Icom 756 pro ii specifications driver

I can upgrade your radios display to a nice bright LED backlight that will make your radio look like new, and last for years.Ĭost of the upgrade is $140USD, which includes the cost of the LED strip and driver assembly.

#Icom 756 pro ii specifications plus

The displays are currently selling for upwards of $200 USD plus shipping. Icom IC-756 PRO II (IC 756 PRO II IC756PROII) TX expand on IC 756PROII 23 EU models: If you have an IC756PROII version 23 EU-model and want expand the TX range: Read my article placed for IC756PRO and change the diode-row according to 'after version 3' mod. If the CCFL tube itself fails, your either have to buy a new display or source a replacement CCFL tube.

#Icom 756 pro ii specifications manuals

The presentation is in the Microsoft PowerPoint format file. ic- 756 instruction manual ( pdf) get manuals from icom japan: get ic- 756pro user manual: ic- 756pro ii: tech. Watch a Web Presentation (3.2 MB) of all the exciting and advanced features the IC-756PROII has to offer, right in your browser. This is a document in Microsoft Word format written by Icom America's chief engineer. While the transistor can be replaced, the coil is now obsolete. The ICOM IC-756PROII Advanced Operating Guide (only 38 KB). GENERAL: Type: Amateur HF/VHF transceiver: Frequency range: TX: 10-160 m + WARC / 6 m RX: 0.03-60 MHz: Tuning steps: 1 / 10 Hz, 1 / 5 / 9. In the case of the 756PRO radios, this results in either a blown transistor or open inverter coil.

This puts unnecessary stress on the voltage inverter circuit. After this time, the tube usually only reaches half its original brightness.

#Icom 756 pro ii specifications full

This assures that when listening in 3.6kHz, that all of the receiver response is listening in a single sideband (the full 3.6kHz) as opposed to 3. The common CCFL tube has a lifespan of ~20,000 hours. 756 PRO II, PRO III, and 780 users should set their twin passband tuning controls 'SFT' to a +300 carrier shift when listening in 3.6kHz to optimize single sideband fidelity on receive. The point about the Kenwood 590 having a warranty is valid, but dang the Icom is a much nicer.

I really liked the 950 and would still have it but the chance at the Icom came along. The Icom is a very nice receiver and the band scope is more useful then on the Yaesu 1200s.

#Icom 756 pro ii specifications series

Secure gently two screws on the motor clutch.Is the display in your 756PRO series radio starting to dim?ĭoes it take five or ten minutes or more to reach full brightness? I replaced an FT950 with an Icom 756 pro 2. NOTE - good idea is to add small drop of machine oil, or silicon grease, but just "small" drop.Īfter reassembly the cover don't forget to check if brake nozzle fit in right direction as marked before.Īttach the motor to ATU chassis, put again attention that brake nozzle should is positioned as on the picture, with variable capacitor at his max capacitance (closed). Last thing we need is to secure upper cover of the motor - screwdriver with small 100g hammer or electric pliers will do the job. Otherwise You'll have to open the cover again, or pray not to destroy the motor turning it by hand later. Assure that it's almost same as on my pics. NOTE: Before securing the cover, check orientation of the main output shaft with metal nozzle. The issue I am experiencing is about 9 times out of 10, when a station connects to me and I send my report, they never come back or they just keep sending their Grid Square info.

Let the epoxy solidify, and after few hours ( or minutes ) carefully examine the surface of the magnet, bottom and upper ring, remove any glue marks or dirt with sharp knife.